Saturday, June 12, 2010

The Red Floral KK knit top

Here is my latest knit top:


This pattern was made similarly to the black and white one, except this time I didn't lower the front shoulder angle.

I DID reduce both the CENTER FRONT LENGTH and the FRONT SHOULDER SLOPE measurements by 0.5", though, because I knew the knit fabric would stretch to accomodate my body's curves in front...and using a shorter CFL produces a smaller bust dart, so there is less dart to 'get rid of' from the start.

I also INCREASED my BUST measurement from 41.5" to 42"...not much, but this also made the bust dart smaller, so there was less dart to eliminate in the process of going 'dartless'.


Also, I INCREASED the SHOULDER LENGTH measurement in my chart for this one...because when I rotate that remaining little dart closed, it increases the width of the neck opening on the front pattern. By increasing the SHL I have created a more-narrow front neck to start with, so that when I rotate the little dart closed, the resulting front neck width matches the back neck width.


I DID NOT scale this pattern at all...I used it as drafted, with zero bust ease. In hindsight, I *should* have used MORE hip ease, then scaled it smaller, because I had increased both the shoulder and bust measurements! duh. But it is very wearable...the ladies in my sewing guild liked the extra ease. BTW, the back neck depth is 0.75".


There is a bit of 'drapery' under the arms, both in front and back. Part of this is the excess bust ease, but also, part of it is due to the shoulder angles being the same as for WOVEN fabrics. I should have lowered the shoulder angle after all! I have decided that for next time, I will lower the back shoulder angle by .375" and will lower the front shoulder angle by .75"...twice as much in front as in back. You can see by the picture below that when I pinch the shoulders UP, the drapery is lessened.


So, I *think* I have finally figured out how to get a good dartless pattern using my Patternmaster Boutique software! Yes, it takes some manipulation, but not alot...and certainly much less manipulations that I have to go through to alter a commercial pattern! And it only took 11 years to figure it out! ;)

Oh, and the 'KK' in the title stands for Klassy Katz...the fabric store where this fabric was purchased!
Here are my drafting choices:
Style Name: 100520_4_dartless_tiny_dart
Date: 5/20/2010
Last Update: April 1, 2010
Chart: Trish 050710_4Drtls_tinydt

Garment Type: Blouse
Style: Blouse
Closure: Front Zipper
Front Neckline: Scoop
Back Neckline: Jewel
Hemline Sweep: Straight
Hemline Shape: Straight
Front Darts: Side
Back Darts: No Darts
Sideseam Shape: Fitted

Front Waist Darts: 2
Back Waist Darts: 1

Front Neckline Depth: 4
Back Neckline Depth: 0.75
Neckline Width: 1
Neckline Point: 0

Armhole Depth: 0
Dart Override: -0.625

Side/Arm Point: -1
Side/Waist Point: 0
Side/Hip Point: 0

Cf/Extension: 0
Cb/Extension: 0

Shoulder Pad: 0
Shoulder Point: 0

Finished Cb/Hem Length: 24
Hip Depth: 8

Bust Pt Vertical: 10.25
Bust Pt Horizontal: 5
Upper Front Dart Length: 1
Upper Back Dart Length: 1
Lower Front Dart Length: 4.75
Lower Back Dart Length: 4.75
Back Shoulder Dart Length: 3


Sleeve Style: Set In
Sleeve Underarm Seam: Tapered
Sleeve Hemline Shape: Straight
Sleeve Length: Short
Sleeve Cap Ease: 0.35
Sleeve Underarm Length: 2
Sleeve Overarm Length: 7.849
Sleeve Hem Circumference: 15
Sleeve Elbow Depth: 8
Sleeve Elbow Circum.: 10
Sleeve Cap Height Adj: -0.75
Front Armhole Shape Down: -0.3 clicks
Back Armhole Shape Right: 0.2 clicks


Seam Allowance: 0.375
Hem Allowance: 2
Facing Width: 2

Chest Ease: 0
Waist Ease: 0
Hip Ease: 1


Body Measurements

Chest Circumference: 42******increased by 0.5”
Back Shoulder Width: 15.75
Neck Circumference: 13
Natural Waist: 35
Hip Circumference: 41
Crotch Length: 29
Height: 66
Weight: 98:)
Bra Cup Size: D
Center Front Length: 14.5***reduced by 0.5”
Front Shoulder Width: 15
Front Shoulder Slope: 18***reduced by 0.5”
Shoulder Length: 5.375**********increased by 0.375”
Center Back Length: 16.5
Back Shoulder Slope: 17.875
Bicep Circumference: 12

Notes:
duplicating/improving NOVeDrtls6 CSL2

DARTLESS 4 has 42 bust and longer SHL...which makes Fneck .5" narrower than Bneck...so rotating bu dart closed will equalize the neck widths

2 comments:

Grammy aka Marilyn said...

I am enjoying following your dartless top 'adventures'. I used the settings for a DT that you posted on the PMB forum quite awhile ago, and it gave me a pretty good top--although quite a bit longer in the back than front. I think I just ended up cutting the back shorter--must have even curved it to match at the SS.

Anyway, I am curious about your comment to 'rotate the bu dart closed' to equalize the neck widths. When rotating the dart closed, are you selecting the shoulder seam and the top of the armhole? This is how I would visualize it, and then you just have to redraw the front neck curve slightly. Right?

Nice job. You are a few steps ahead of me in pattern drafting, and I have learned quite a bit from your postings--here and on the forum. Thank you.

Marilyn R in IL

Trish said...

Hi Marilyn! Nice to see you here!
The purpose of rotating the bu dart closed was not specifically to equalize the neck widths...I just realized that when I did rotate the bu dart closed, it made the front neck narrower than it started out (so I took advantage of that!).

Yes, I select everything above the bu dart (which is in the ah)...that means the upper part of the armhole and the shoulder and neck (even upper CF line)...pivot point is on CF seam. Then I redrew that CF seam to be straight again...you can see the image on my previous post...

http://makeitfit-trish.blogspot.com/2010/06/as-happens-every-summer-i-am-once-again.html

Thanks for taking the time to comment!
P

 
Free Hit Counter