Aqua Fitted Princess and Kimono

Back in April, right after the wedding, I worked a bit on fitting a knit top.  Although it wasn't perfect, the improved fit of the MOG dress had me raring to go, anxious to see if I could improve the fit of the knit garments too.

Ok, that was PART of the inspiration, but there was more.  I had fabric that was tempting me.

Last Fall, when shopping for the MOG dress, I stumbled onto some fabric at THE FABRIC SOURCE in Jackson, TN.  It was a floral printed stretch tulle.  Precut into approximately 2yd lengths, I bought 2 of them, for $5 each.  They provided instructions for a no-sew swimsuit coverup...you just cut it into a big oval and cut out armholes. 

Well, also on that same trip, we stopped and did a bit of shopping at FELICIA BELLA BOUTIQUE, also in Jackson.  I had tried on a long-sleeved pullover made of...you guessed it!...printed stretch tulle!  I didn't buy it because it was nearly $60!  But I studied it as closely as I could in this not-so-private dressing room.  I even did a bit of measuring!  It seemed to be almost a long tube with two holes in the middle...one for the body and one for the head. 

Inspired by the memory of that top, and wanting to use this fabric to get it out of my way,, I decided to start cutting.  I layed out the fabric on my table and cut what I hoped would be similar to the shape I had tried on (months ago!). 

Well, it wasn't good.  So I went to the computer and opened my PMB software!  I drafted a KIMONO pullover, then compared the patterns on screen.

As you can see, there wasn't much difference between the front and back patterns. 
Here, the front is RED.

 I decided that I would just use the BACK PATTERN...but I still didn't want to have to print it, because, after all, this was simple, right?

So I measured it!  Then I could print this diagram on one piece of paper, take it to the fabric and measure and cut.  It seemed like a good plan.

There was ONE PLACE I was having a hard time just winging it...and that was the sideseam/underarm area.  So I printed ONLY that area and placed it where the measurements dictated:

Above is the sideseam...the right edge of this paper is the cutting line.
Once I began actually plotting out my cuts, I made another change.  I LOWERED the angle of the arm by 3 inches....shown below by the dark blue line.

But after sewing this (yet again), I still wasn't happy with the way the sleeves draped.  I knew this was gonna be loose and drapey, but I didn't want it twisting!  And yes, the sleeves seemed kinda twisty.  So I ripped and reshaped the FRONT sleeve to lower the over-sleeve seam by 2" at wrist AND, I shorted that seam by 2" also.  This allowed me to ease the back seam to the front, creating fullness in back and eliminating the twisting.  Good enough! 

**

I hemmed the neck and lower edge, as well as the sleeves, with the coverstitch machine, turning a small hem to the backside.

Now it was time to make something to wear UNDER this!  I drafted a fairly closely fitted Princess seamed tank and cut it from some cotton interlock.  Oh dear.

Remember?  Back in the post about the ZERO EASE TORSO BLOCK, I discussed the armhole shape and how I was lowering the notch on the BACK armhole so it would coincide with my body's ah measurement...but I was NOT doing it on the front armhole because it just looked 'too scooped'.  Well, after sewing the MOG dress and realizing that the armholes were still not perfect, I decided to give it a try.  I used the AH SHAPE TOOL to lower the front notch until the distance from shoulder to notch matched the distance on my body from shoulder to the V-crease where arm meets body...look back at the HELPING MEASUREMENTS if you need further explanation.

Here is the pattern I came up with.

You can (hopefully) see how very 'J' shaped that front armhole is!  Pattern on the left, FYI.

As I said--Oh dear.

Or, rather--

OH.MAH.GAH. BECKY, Look at that armhole!

The front armhole was WAY too scooped...making this top potentially a wadder. 

The shoulder angle seemed ok, though.
Overall, it wasn't totally unfortunate.

I was SHOCKED by the back:  I think this is the first time ever that the back neck has actually come up to the bone where the back neck is supposed to come to!  I put in a pin to show where I will lower the neck to.

I liked this style and this fabric, though, knew I had to find a way to salvage this top.

 

Somehow I got it into my mind that I should NOT have used the E cup to draft with after all...and that I needed to shorten the whole upper front, which I could do by ripping the shoulders and cutting off the front shoulder before resewing them....so I did.***

***later evaluation of the fit proved the front was now a tiny bit too short...that front length was needed and should NOT have been whacked off!  It was those goofy armholes making me crazy.  

Anyway, I decided that I could create some facing-like pieces...like a yoke, perhaps...that could be sewn on to fill in the missing area of the F-armhole.  So I went back to the computer/drafter.

Since I had felt the need to shorten the upper front, the obvious conclusion (to me, that day) was that I had used a bust cup size that was too large (E) and should reduce it.  So I did.

***another spoiler alert!  Bad idea...but I got away with it on this top, this time.

Here you can see the NEW FRONT PATTERN (in RED) superimposed on the old pattern.  The new front is shorter at the shoulder.  The new pattern has a smaller bust dart (so the angle of the upper front is different) and the new armhole is both higher and less scooped (The back armhole is higher on the new pattern, too, but I didn't show that).

I aligned the sides to the center pieces and created 'yokes' that could be cut from the remnants I had left.

 But I needed to know WHERE to trim off the existing garment so I could sew on those yokes!  So I created and printed little 'yokes'  from the original pattern, too, and used them like templates to show me where to cut.  The upper pieces in this image are the 'cutting patterns' and the lower pieces are the new yokes to be sewn on.  you can see that, on the FRONT pattern, there will not be much cut off in the 'scooped' area!   But there WILL be quite a bit added back on, via the yoke, in that area.



And it worked!  It actually looked pretty good...like a design element!  I had top-stitched the seams with the cover-stitch machine, so I top-stitched the new yoke seams, too.

Here is what it looked like right after sewing:

Front--

 And back--

As you can see, there is some fullness (rippling) in the back armhole that I didn't notice at the time.  I used clear elastic to stabilize the neck and armhole edges when hemming.  But it wasn't until earlier LAST WEEK that I realized WHY this might be happening. 

I was discussing a program issue with Tech Support Karen...the Dart Override tool isn't working with my numbers...and she asked my why I was enlarging the armhole by raising the shoulder with the SHOULDER HEIGHT TOOL but then trying to shorten the Front Armhole with the Dart Override.

Well, the SHOULDER HEIGHT TOOL affects both front and back patterns, but the DART OVERRIDE tool only affects the FRONT armhole (or at least, that is how it is supposed to work) by putting some of the bust dart into the armhole OR by stealing some of the front armhole to enlarge the bust dart (this is what I was trying to do).

So, even though they do two different things, it did get me thinking about the shoulder height setting and 'what if'...

Up to this point, I have been operating on the assumption that the pattern's shoulder angle was correct for me (and my square shoulders) when I raised that setting 0.5". 

But further reflection has me thinking that:

• a) lowering the shoulder tip by 0.5" might eliminate that back ah rippling, and
• b) I should have just lowered the F-shoulder tip in front instead of whacking off the whole front shoulder!  This was kind of a light-bulb moment.

So, for the NEXT ONE......I will NOT raise the shoulder height.  We will see how that does!
And I will go back to the E cup, which is what I should be using.  But I will NOT scoop those front armholes to force the measurements to match my body's measurements!  obviously, the front notch is NOT supposed to be an anatomical location!

MOG Dress Construction, Pt 1

I had a difficult time deciding on fabric to use for my MOG dress.  There was not a huge selection of fabric at my local Hancock Fabric stores...I visited 3 in my area, as well as the Joann's Fabric store!  I really wanted to use silk, but that was not to be, unless I wanted a pale oyster color (which Klassy Katz had!).  I did not want pale oyster or any other pale color.  After trying on a gazillion RTW dresses, I knew I needed a strong color....preferably a jewel tone. 

The MOB had a teal dress so I could not use that.

I finally settled on a polyester crepe-back satin from the BFF line (by Lauren Hancock). There was a coordinating lace, but it wasn't special...not reimbroidered or anything. But this was the best I could do locally and I had procrastinated too long to shop the internet and send off for samples...so I purchased this grape hyacinth-colored fabric.  

As I was trolling the aisles, hoping to stumble onto something better before I had this cut, I spied an odd mesh fabric...it was both purple and gold!  I wondered...what if?

So I bought some of that mesh fabric as well!  I decided to use it UNDER the lace...that way, the dress would have some sparkle without my having to add beads!

I cut each layer of the bodice separately...that is, I cut each piece from 3 different fabrics, one fabric at a time.

As you can see, I bought more than enough fabric...there is plenty of gold mesh left over for more fun things!

And when the lady cut my 3 yards of lace (I only really needed 1.5 but had allowed for experimentation), she used her 'gun' to scan the price on the bolt and said, "Do you know how much this lace is?"
Oh dear, I thought.  "Yes, it is $9.99, but on sale for 30% off."
She was shaking her head, no.  She stuttered a bit..."It is 21---er--"...pause (my heart fluttered...21?)..."seventy cents per yard."
Both of us were sure it was a mistake, but she said she couldn't change it.  I bought all 8 yards!  and for less than the regular cost of one yard!  So I have lots of lace, too!

Once the layers were cut out, I carefully aligned each one and glue-basted them together around the edges. This way, once the glue dried, it could be treated as one layer.

Here you can kinda get an idea of what this looks like once the fabrics are layered.  The gold mesh really added a richness that the lace alone lacked.

I don't know WHAT I will do with all the leftover lace!

Here are the bodice pieces, front and back, all lined up as they fit together.  The FRONT pieces are on top, and the BACK pieces at the bottom.

I serge-finished the edges of the vertical seams before sewing these pieces together.

Turns out, that was not necessary, and was actually not helpful, so much of it was eventually ripped out.

Once the vertical (princess) seams were sewn, the seam allowances were clipped and notched to allow for spread.  This made it easier to remove the unneccesary serger threads!

The bodice pieces went together fairly fast and smoothly.  Then it was time to work on the midriff section.  so back to the drawing board...er, drafting program! 

Once the pattern was made for the midriff, I started to work. I found this woven fabric in my stash of interfacings...I think it was originally purchased to make 'rangers' for jackets...you know, those two pieces of interfacing that encompass the back neck and shoulder and one armhole...they cross in back, giving support and movement.

Anyway, I decided it would be a good foundation layer for my midriff.

I cut my midriff pieces from the woven fabric, then marked and sewed the darts.


How funny it looks once the darts force it to take shape!


Now, at this point, I wasn't sure exactly HOW I was gonna get the midriff done.  I tried DRAPING the fashion fabric over this foundation...for about 27 seconds...!  t
Then I came to my senses!  I am a flat-pattern thinker...my brain just doesn't like to drape.



But then I got a wild idea.



WHAT IF I pleated the fabric BEFORE I put it on the foundation?

I have a pleater board that I made several years ago...it was a sewing guild project and we all made one.  So I pulled it out and set to work.

I put the right side DOWN toward the pleater board (I am using the crepe side, not the satin side, as my 'right' side) and began pushing the fabric under the 'lips' of the pleater board...skipping every other one.

Then, I used an iron-on tricot interfacing and pressed it onto the fabric to hold the pleats in place.

I did a wide section for the front, then two smaller sections for each half of the back. 
This took A LOT of fabric!

Once I had my pieces pleated, I began to consider once again HOW I was going to attach this to the foundation.

uh oh.

Even though I had cut this fabric on the bias before pleating it...so it would have lots of 'give'...it was still NOT possible to force this pleated piece to have the same shape as the foundation pieces. 

Rats! 

No, the dart shaping had to be incorporated. 
I went back to the computer and created a new pattern piece for the pleated midriff.

Since the Empire waist was 3" above the waistline and the midriff extended 6" below the waistline, my midriff section was 9" tall.  I divided that into 6 equal parts...1.5" each.

Then I separated the sections and added folding lines, then closed the dart fragments in each section.


I ended up with two sections with opposing curves which would be joined at the waist.

So I cut these pieces from some more fabric...again, placing them on the bias...and began sewing these pleats in.  I folded on the fold lines, then basted on the pleat lines.  Once the pieces were pleated I began hand-sewing them to the foundation.

It was awful.  The bias stretched, causing weird bumps.

So I decided it couldn't be bias.  AGAIN, I cut new fabric to try anew.  I was worried that I might run out of fabric...and I had purchased THE WHOLE BOLT...there was nothing left at the store to go back and get should I run out!

This time I decided to pleat the fabric ONTO the foundation.  I aligned the top edges and pinned.  Then I sewed on the fold line, then folded the fabric upward and pressed...then basted on the pleat line, and sewed again about 3/16th" below that...so that once the basting was removed, the pleat would stay partially closed.  Then I would press the fabric downward again and sew on the next foldline...etc. 

Well, when I got the second pleat done, I realized that the FIRST pleat didn't measure 1.5" as planned.  It was only 1.25".  I decided NO BIG DEAL...I would make the second pleat 1.375", then the third and remaining pleats would be 1.5" and no one would know the difference.

Well, the math didn't work out that way.  once I got to the bottom, there was too much fabric for just one pleat, but not enough space for two pleats with the correct spacing.  I had to start over yet again!

Each time I started over, I had to cut a new foundation...because it wasn't worth ripping out all those pleats to salvage the foundation!

So once again, I pinned the top edge to the foundation and began pleating the fashion fabric to the foundation...this time MEASURING VERY CAREFULLY!  Each pleat was 1.5" wide.

Once the upper section was done, the lower section was begun.

I sewed the waist of the lower section to the waist of the upper section and continued with the pleating.

I even added my machine's quilting guide to help make sure that each pleat was precisely sewn!

Once the midriff sections were finally pleated, I could sew them each to their respective bodice piece. 

FINALLY, it was time to put in the zipper!  My choices were limited...the best color match was not an invisible zip, but in the end I decided to use the invisible one.

I put in the zipper, stopping the top about 7" below the neckline.  I wanted a slit in back but wanted it to be short enough that the dress would cover my bra band!

Once the zipper was in, I could finally sew all the bodice pieces together, front and back, and try this thing on!  Yay!

Well, not yay.  It was too 'blousey' under my bust!  Ugh! 

Even though I had sewn a trial muslin, it was NOT an Empire waisted one.  And we all know that an Empire waist fits more snugly around the ribs than a top with a 'regular' waist.  I was pissed.

Just like in that Pleated Dress I needed to make the waist dart wider at its upper end!  I could pinch out 0.5" under each princess seam at the Empire seam.

I took it apart.  I resewed the lower end of the princess seam (below bust point) to remove additional fabric (0.5"). 

Plus, I had allowed a 1" SEAM ALLOWANCE at the bodice Empire seam (just in case) and had decided I needed to use it all. Well, once the midriff was sewn to the bodice, I DID NOT need that extra!  It was too blousey in length under the bust as well!  so, I also removed this excess length from the front bodice at this time.

Then I looked at that midriff section that I had painstakingly pleated (ad nauseum)...I didn't cry, but I should have!  No, instead I began ripping. 

I ripped the waist seam and the seams holding the pleats ABOVE the waist.  I was finally able to remove the piece of fabric that was the upper front midriff.

I could easily sew the waist dart of the foundation piece larger...basically, it was correct at waist and below, but needed to be sewn straight up from waist to the Empire seam.

Well, think about this....if the dart is wider, that means the SHAPE of the pattern piece that represents the fashion fabric  has now changed, too! So I could NOT reuse the fabric...I had to (yet again) cut another piece of fabric for this upper front midriff section!  At this point, I am measuring to be sure there is enough left to cut a skirt!  There was...

So, I folded out the corrected dart on the pattern and cut the new piece.  Now, HOW am I gonna do this...since the midriff was initially formed by sewing the pleats from the top down?  Basically, I had to sew a lot of it by hand. 

Funny...after hand-sewing for a while, I was thinking to myself, 'this is so much more ZEN than shopping for a dress.'  But I had to laugh at this thought, because only a few hours earlier I wanted to tear my hair out!

I resewed the front midriff to the front bodice.  But remember? I had allowed that 1" seam allowance on the bodice that needed to be removed...ON THE BACK, TOO! 

So, now I had to RIP OUT THE INVISIBLE ZIPPER and remove the excess 3/8" length on the back bodice....then resew the bodice and midriff sections and reinsert that zipper.

Eventually I got the front and back put back together with the zipper in...and it fit!  Now it was time to draft the skirt...

To be continued.

Navy Dress part 3

After several days had passed since wearing the dress for the first time (to the wedding), I had been 'away' from the dress long enough to re-address the 'issues' I had with it before wearing it again the following weekend. I called my sister, who came right over to help me evaluate it. I put it on. Immediately, she could tell that it needed to be shorter. Bummer...but I kinda knew that it was too long. I even knew the back was longer than the front, but because of that vent/kick pleat and the number of times I had sewn and ripped it, I had been VERY reluctant to rip again to hem the dress shorter. But I knew that was what was needed, so I was willing.

She also thought the Vneck should be lower, and again, I agreed (hem up, neckline down!). Plus, she wanted me to tighten it up UNDER the bust...contouring the princess seam a bit. So I began working on the neckline and princess seam adjustments, planning to take the dress to her house afterwards so she could mark the desired hem length for me once the alterations were done.

I messed with taking that princess seam up and letting it out about a thousand times! I was adjusting the tiniest amounts...sometimes barely a thread's width! Eventually, I got it to suit me.

Lowering the neckline was no treat, either. I had understitched the facing and there was a lining involved, so 'internal access' was limited! I did have to rip out the thread chains I had used to tie the lining to the hem and that made it easier to get up inside the lining. Actually, I had ripped the stitching and understitching once before...when I first realized that the front was a little shorter than the back, I tried to let out the front shoulders. I ripped the neck facing (not fun...black and navy!) and did let out one side. But it made so little difference that I decided it was not worth the trouble, so I didn't bother with the other shoulder. So I was really looking forward to ripping the neck again, this time to lower it. Not. But I did it and it made a difference...and improvement!

So now I was ready to get the hem marked to shorten the dress...

When I took the dress to my sister's house so she could pin up the hem for me, we also decided it would look better if I reduced the hem circumference....tapered/pegged the hem a bit. So when I got home with it, I had to redo the sideseams (yet again!) to taper the hem before I could begin the actual hemming! But tapering made a WORLD of difference in the way the dress looked! Before, with the hem being as wide as the hip area, the hem actually looked WIDER because my body has less F to B depth at hem level, so the dress hung wider and less deep than at hip level where my body thickness forced it to be deeper and therefore, less wide. By tapering the hem, this reduced the visual width at hem level to be more similar to the visual width at hip level. To determine HOW MUCH to taper the sideseams, I opened PMB and compared the width of the hem using both the STRAIGHT and TAPERED Hemline Sweep. I decided that since the program reduced the hem at each side seam by .75", that is what I would also do...I tapered each sidedseam from hip level to a point = .75" inside at hem. Better!

Unenthusiastically, I struggled through shortening the dress, which entailed a lot of ripping at that back vent. And remember the interfacing that I had fused to the bottom of the dress, so my hem handstitching wouldn't show? Well, turns out, that hem showed anyway, despite the interfacing and my best efforts at hiding those stitches. It was just the nature of that fabric. Well, shortening the dress removed a lot of that interfacing. Since the original hem stitches showed anyway, I decided that THIS TIME, I would just hem the dress using the blindstitch of my sewing machine, rather than take the time to hand stitch it again. Turns out, it had about the same 'invisibility' as before and was much quicker!

After taking in the dress under the bust, my arm mobility was decreased somewhat as compared to the first time I wore the dress. It was still not too bad, but I was aware of the difference. I think I needed a higher armhole, especially as the dress became closer fitting.

I had originally envisioned this dress having beaded trim around the neck but had run out of time before the wedding. I had time now, though (or so I thought!). DSis suggested trim at the sleeve hems would also look nice. So together we went to our local Hancock Fabric store to see what they had. I found a black trim that I could sew beads to...I had plenty of beads at home that would work.

At home, I measured and cut the trim pieces to length, secured the ends to prevent ravelling, then began hand-beading them...ON THE DAY OF THE PARTY! Yep, it was the day of the paty by the time I got to this part. I was running way behind on this remodel! And I don't work fast!!! It was after 4:30 pm when finally got all the beads sewn onto the trim, but the trim was not yet sewn onto the dress! BTW, it was during these hours that DH decided to 'clear' the camera's memory card... sigh.

As it got later and later, my stitches got bigger and bigger...I was sewing as fast as I could to finish sewing the trim to the dress! Finally the trim was on. I made new thread chains to reattach the lining to the dress hem and I was DONE!

I actually finished the dress at 6:30...the party started at 7:00!

I flew to my room to touch up my makeup and comb my hair and we were outta there! And we arrived right on time! It was a good dress for the occasion...Une Grand Souire...a wine tasting and art auction. I looked as good as anyone else there (better than some!) yet didn't look over-dressed.

The pictures of me in the dress were taken after arriving home later that night. I hope my hair looked better earlier!

Navy Dress Part 2

I have been trying to update my progress on this dress, but have failed miserably! It HAS been finished and even worn...twice now! But it was not an easy project! This thing has almost kicked my butt!!! Everything has been more complicated that it should be!

I spent time researching how to do the facing at cb when there is a zipper there...in the end, it was easy, but I *thought* it would be hard so was apprehensive. Basically, I have made everything harder than it needed to be, which *is* my Modus Operandi!



But let me back up a bit...

Since I didn't want to compromise the 'breathability' of this fabric, I chose NOT to underline the dress, as I DID plan to line it. So I fused strips of interfacing above the hem area, so that my hem stitches could catch something other than just the fabric, and hopefully, be invisible. More on this later.

I inserted an invisible zipper...hadn't done one in a while...and my stitching was not quite as close to the zipper teeth as it needed to be to remain 'invisible'...so I stitched each side again a bit closer. Then I zipped it closed. Ackkkk! The cut edges of the neck were not aligned...I had allowed one side of the zipper to shift! I had to rip out one side of the zipper...which had been sewn TWICE!!! And in black thread...on a black zipper. I had to go sit outside on the deck in order to see well enough to rip!

I had taken lots of pictures during the construction of this dress, but DH accidently deleted them before I could upload them to my computer. sigh. He was putting them onto my computer in anticipation of his taking the camera with him to his parents house, and he was doing this while I was very busy and unable to supervise where all my pics were on the memory card and where they should go on my computer. Some were deleted, some were not. sigh.


Next was the French pleat at the back hem. This kick pleat is the slit with underlap kind...oh why did I have to do a French vent? A simple slit would have looked just as nice, even showed a bit of leg! But I planned this without regard for that. And lining a French vent is tricky if you haven't done it in along time, epsecially if you have never been the one to make the pattern! Anytime I have done this in the past, the pattern was made by a professional patternmaker and a template was provided to 'adjust' the lining. Well, this time, I had to make my own pattern and figure out my own 'template' for adjusting the lining!!! And of course, I did it wrong at first...allowed too much seam allowance on the lining edge, so that when the edge of the lining was sewn to the edge of the vent flap, there was excess lining width. Had to rip and resew. Then realized I should have HEMMED the lining before sewing it to this edge of the vent flap. Rip again, then hem and resew. Sheesh! of course...my pictures detailing the steps are gone. sigh. I can show the end result.

Once the zipper was in and the princess and side seams were sewn, I tried the dress on. It was 'roomy' to say the least! I had allowed 5" of hip ease and 2" waist ease...apparently that was too much. I took in the sideseams from above waist to the hem to remove 1" circumference...better.

There was still a fullness above the bust, especially on one side. I decided this was because I really needed a bit more length in the front bodice above the underarm level, which made the front bust level a bit too high. I need an additional 3/8" front length....which also would draft a larger bust dart...but that is for next time! I decided I couldn't fix the Bust Height problem in this dress so I moved on.

I had not yet set the sleeves, but the depth of the armholes was bothering me. I was afraid I had drafted the armholes too deep. I do have square shoulders and often need to raise the AH depth, but had failed to do that. duh. Then I realized that the AHs had stretched....why hadn't I staystitched? duh. I put the pattern on the ironing board and aligned the garment onto its pattern and steamed the AHs back to size and shape, then used some fusible tape to keep them stable...sorry, that picture was deleted. sigh. I'll take one of the fusible product I used to 'fix' the AHs.

Now on to the sleeves: The first set of sleeves were bad (cap height was too low, and I had not allowed enough cap ease), so I redrafted, created and cut new sleeves. This time, I basted the sleeves in! Still not perfect, but usable, once I rotated them a little to look/hang better.

But before I made those new sleeves, though, I wanted to address that b-AH. I was considering trimming out the back armhole, as if removing the 3 clicks outward that had I added during drafting by using the AH Shape tool. I felt like the back was too wide, but I sure did hate to try this, as once cut, this alteration could not be undone! Finally, I did it. And the new sleeves went in nicely!

When cutting out the sleeve lining, I forgot to cut the front underarm area a bit higher than the pattern (to allow extra fabric so the lining will have room to go over the underarm seam allowance)...so I figured I might as well NOT cut the back higher either....so then I had to decide HOW to do the sleeves. In the end, I just sewed the lining's armhole to the garment's armhole...to treat them as one. Then I lined the sleeves separately...then inserted the garment sleeves into the dress by machine, and sewed the lining sleeves to the lining AH by hand. Not my preferred way to do it, but it worked!

The dress feels wonderful as I put it on. I lined it with Bemberg rayon...my first time to use this. I really like the way it feels! I had some issues sewing it, though. I didn't change needles between the shell and the lining, and after sewing nearly ALL the lining seams, I realized I had 'loops' on the bobbin side every now and them...and had to go back and reinforce some of the stitching. I don't know what would cause this, unless it was the needle size.

Then I wore the dress to the wedding. It wore well...was comfortable and allowed adequate mobility. However, I felt like I looked like my grandmother. I was NOT happy.

Navy Dress Part 1

I'm still working on the dress, but at least I am in the sewing stage! Today, I will finish cutting out the lining and begin assembling and inserting it into the already sewn dress. Well, the dress's sleeves have not been inserted, but other than that, it is 'already sewn'.

I decided to go with a shoulder princess-seamed version; Vneck; with 3/4 length sleeves (the cap sleeves I was considering just didn't do my body any favors); vent/kick pleat in the back seam. I am making it 'just-below-the-knee' length...I chose 43" as my finished back length. I also made this straight (as in, no flare) but again, I am not sure that was the best choice either! Those 'hams' just under my back waistline (on each side) are trying their best to be the star of the show!

The fabric is a navy poly/rayon blend, and it is either a jacquard or a matelassee...I have no idea how to spell that, and am not even sure of the pronounciation! I goofed when I cut out the center back piece...I was on the phone while cutting, so my attention was diverted when I layed that piece onto the fabric after cutting the other 3 pieces--front, side/front, and side/back---which all fit nicely across the width of the fabric. I cut those 3 pieces, then pulled more fabric onto the cutting mat to lay out and cut the CB, sleeve, facings, etc...and, well, I was distracted and forgot to consider the pattern repeat! In this picture, you can see how that CB and Side/Back would have related to each other...I had to slide the back piece upward, as in the right side, to align the design repeat. So I cut a new CB piece that DID keep the fabric's repeat aligned! Thank Goodness I had extra fabric!

Regarding the pattern...

• I found that I needed to draft with 2" extra hip ease than desired, because the long front dart extensions need to remove a full inch on each side...for a 2" reduction in front.


• And it turns out that using a Side/Hip placement of (+0.5..moving the SS/hip backwards) gives me mirrored sideseams, which is desirable to me! Although this initially makes the front pattern WIDER than the back pattern at hip level, after I sew out the long front waist darts, the back becomes wider than the front...which is more logical, since there is a bum back there!

I think I might have to tweak my CFL measurement just slightly (for next time) to provide a bit more front length to make garments better conform to my shape...that is, I need MORE than just 'adequate' front length if I want the garment to sit closer to the rib cage under the bust, as opposed to falling straight toward waist.

I drafted this with 7" of hip ease , thinking that after I sewed out the front waist darts, I would have 5" ease. Well, 5" turned out to be too much. I ended up sewing out an inch at both waist and hip...all the way to hem. So 4" hip ease and 1" waist ease turned out to be good for me on this dress. My choice of bust ease was 1.5". More on drafting this later...